Substrate preparation
The surfaces to be glued must be clean, and in particular free of oil, grease or release agents.
Processing
The adhesive is applied on one side (small areas) or on both sides in a very thin, even and covering layer with a brush, spatula or roller. Absorbent, rough surfaces usually require a slightly heavier application or a second application after the first has dried.
Immediately after the adhesive has been applied, the substrates are joined together with light contact pressure. It must be ensured that the bonded materials remain in contact. If necessary, press again until a sufficient initial tack is reached and fix against slipping.
An assessment of the final strength and resistance can only be made after a few days!
Specific property
The Technicoll® special adhesive included in the set can also be used to repair minor damage to inflatable whirlpools, PVC garden pools and swimming pool liners made of soft PVC under water.
To do this, the appropriate PVC repair patch is coated with the adhesive and immediately pressed under water on the damaged area and rubbed in until the necessary initial adhesion is achieved. Air and water temperatures below +15 °C can lead to reduced bonding results!
Product information/technical data sheet for Technicoll® adhesive
Application
Bonding of flexible PVC foils to one another, as well as to rigid PVC and other materials.
Application examples
TAMI dog boxes, standup paddle boards (SUP), inflatable boats, swimming pool liners, pond liners and vehicle tarpaulins made of soft PVC. For re-gluing and repair work, PVC pipes.
Processing instructions/product data
Viscosity (+23 °C)
Color: colorless, transparent
Wet bonding time: Approx. 10 to 30 seconds (one-sided application) max. 1 minute (two-sided application)
Order type: one and both sides
Processing temperature: +15 °C to +25 °C
Cleaning: Cured adhesive can only be removed mechanically.
Permissible storage time:
At least 3 years when stored in a cool and dry place in the closed original container.
Preferred storage temperature: +10 °C to +25 °C
Cold behavior: Not sensitive to frost. thickening at lower temperatures. Fully usable after tempering to processing temperature.
Preferred materials:
• PVC-soft (PVC-P) wood materials
• Hard PVC (PVC-U) with each other and with textiles
• Artificial leather, paper, cardboard
• PUR foam
Not suitable for: PE, PP, PTFE (Teflon®), POM, silicone, EPDM,
PS rigid foams (e.g. Styropor®)
Due to the large number of possible materials and differences in adhesion behavior, adhesion tests are necessary before practical use.
Product Information/Technical Data Sheet
Application
Bonding of soft PVC films with each other, as well as with rigid PVC and other materials.
Application Examples
Stand-up paddle boards (SUP), inflatable boats, swimming pool liners, pond liners, and vehicle tarpaulins made of soft PVC. Suitable for new bonding and repair work, PVC pipes.
Processing Instructions/Product Data
Base
Polymer
Viscosity (+23 °C)
Approx. 550 mPas
Solids Content
Approx. 27%
Density
1.0 g/cm³
Color
Colorless, transparent
Wet Bonding Time
Approx. 10 to 30 seconds (single-sided application), max. 1 minute (double-sided application)
Application Method
Single-sided and double-sided
Processing Temperature
+15 °C to +25 °C
Consumption
150 - 250 g/m²
Cleaning
Cured adhesive can only be removed mechanically.
Permissible Storage Time
At least 3 years when stored cool and dry in the sealed original container.
Preferred Storage Temperature
+10 °C to +25 °C
Cold Behavior
Not sensitive to frost. Thickening at lower temperatures. Fully usable after tempering to processing temperature.
Preferred Materials
• Soft PVC (PVC-P) → Wood-based materials
• Rigid PVC (PVC-U) with each other as well as with → Textiles
• Artificial leather → Paper, cardboard
• PUR foam
Not suitable for: PE, PP, PTFE (Teflon®), POM, silicone, EPDM, rigid PS foams (e.g., Styropor®)
Due to the variety of possible materials and differences in adhesion behavior, adhesion tests are necessary before practical use.
Surface Preparation
Bonding surfaces must be clean, particularly free of oil, grease, or release agents.
Processing
The adhesive is applied single-sided (for small areas) or double-sided in a very thin, even, and complete layer using a brush, spatula, or roller. Absorbent, rough surfaces usually require a slightly heavier application or a second application after the first one has dried.
Immediately after applying the adhesive, the substrates are joined with light pressure. Ensure that the bonded materials remain in contact. If necessary, press again until sufficient initial tack is achieved and secure against slipping.
An assessment of final strength and durability can only be made after several days!
Special Property
Minor damage, e.g., in swimming pool liners made of soft PVC, can also be repaired underwater. The appropriate PVC repair patch is coated with the adhesive and immediately pressed onto the damaged area underwater, rubbing until the necessary initial adhesion is achieved.
Air and water temperatures below +15 °C may result in reduced bonding performance!
Others
.png)
.png)
.png)
.png)
.png)
.png)
.png)
.png)
.png)
.png)
